欢迎进入济南济柴环能燃气发电设备有限公司官网!
当前位置:首页 - 新闻中心 - 行业资讯

行业资讯

燃气发电机组出现爆震现象是怎么回事?

返回 2022.08.31 来源:http://www.huannengpower.com 0
燃气发电机组的控制模块报警提示单缸出现爆震无法正常运行,导致这一现象的原因为什么呢?下面来简单的为您讲解一番吧。
The control module of the gas generator set gives an alarm that the single cylinder can not operate normally due to knocking. What is the reason for this phenomenon? Let me explain briefly for you.
加热值设置不合理,校正系统存在误差;出现了爆震传感器故障或存在电路故障;进气温度过高;进气外立面阀座处或活塞顶部等燃气室中出现大量积碳。具体的诊断方法为:
The setting of heating value is unreasonable, and there is error in the correction system; Knock sensor fault or circuit fault occurs; The intake air temperature is too high; There is a large amount of carbon deposition in the gas chamber such as the valve seat on the intake facade or the top of the piston. The specific diagnosis method is:
检查进气温度是否符合正常标准,依据气体温度高的检查方式进行故障排查;对热值及来气浓度的匹配状况进行检测,对热值进行合理调整,保障修正系统处于100%的运行状态,这一系统若低于95%就会引发爆震;
Check whether the inlet air temperature meets the normal standard, and conduct troubleshooting according to the inspection method of high gas temperature; Detect the matching condition of calorific value and incoming gas concentration, adjust the calorific value reasonably, and ensure that the correction system is in 100% operation state. If the system is lower than 95%, it will cause detonation;
燃气发电机组
燃气发电机组
安装新的传感器以判断原有的传感器是否存在故障问题,并对爆震线路与插头进行检查,如未能发现故障还需布设零时线进行排查;对气缸内气面门以及气门座等位置的积碳情况进行检查,排查气缸内部是否存在泄露情况,先用气缸压表测量,如无异常也可进行拆缸检查。
Install a new sensor to determine whether the original sensor has fault problems, and check the knock circuit and plug. If no fault is found, it is necessary to arrange a zero time line for troubleshooting; Check the carbon deposition at the air valve and valve seat in the cylinder, check whether there is leakage inside the cylinder, measure with the cylinder pressure gauge first, and disassemble the cylinder for inspection if there is no abnormality.
此外在启动过程中,通常会出现启动时电机无转速电池电压恒定不变的情况,有时也会发生盘车有速度但机组难以启动的现象这一现象产生的直接原因通常为电池容量不足接线电缆出现损毁;火花塞等点火系统出现故障;启动电机出现故障问题;启动压力不足等原因。
In addition, in the process of startup, the motor has no speed and the battery voltage is constant. Sometimes, the turning gear has speed but the unit is difficult to start. The direct cause of this phenomenon is usually the insufficient battery capacity and the damage of the wiring cable; Failure of ignition system such as spark plug; Failure of starting motor; Insufficient starting pressure, etc.
燃气发电机组在使用期间可能会出现这样那样的问题,所以为了更顺利的使用起来,建议早些了解相关早些预防,关注我们http://www.huannengpower.com,带你了解更多!
Problems may occur during the use of the gas generator set. Therefore, in order to use it more smoothly, it is recommended to learn about the relevant problems and prevent them earlier and pay attention to us http://www.huannengpower.com Yes, I'll show you more!
新闻搜索
济南济柴环能燃气发电设备有限公司
  • 服务热线

    0531-62325028
    0531-69951266

燃气发电机组出现爆震现象是怎么回事?

燃气发电机组的控制模块报警提示单缸出现爆震无法正常运行,导致这一现象的原因为什么呢?下面来简单的为您讲解一番吧。
The control module of the gas generator set gives an alarm that the single cylinder can not operate normally due to knocking. What is the reason for this phenomenon? Let me explain briefly for you.
加热值设置不合理,校正系统存在误差;出现了爆震传感器故障或存在电路故障;进气温度过高;进气外立面阀座处或活塞顶部等燃气室中出现大量积碳。具体的诊断方法为:
The setting of heating value is unreasonable, and there is error in the correction system; Knock sensor fault or circuit fault occurs; The intake air temperature is too high; There is a large amount of carbon deposition in the gas chamber such as the valve seat on the intake facade or the top of the piston. The specific diagnosis method is:
检查进气温度是否符合正常标准,依据气体温度高的检查方式进行故障排查;对热值及来气浓度的匹配状况进行检测,对热值进行合理调整,保障修正系统处于100%的运行状态,这一系统若低于95%就会引发爆震;
Check whether the inlet air temperature meets the normal standard, and conduct troubleshooting according to the inspection method of high gas temperature; Detect the matching condition of calorific value and incoming gas concentration, adjust the calorific value reasonably, and ensure that the correction system is in 100% operation state. If the system is lower than 95%, it will cause detonation;
燃气发电机组
燃气发电机组
安装新的传感器以判断原有的传感器是否存在故障问题,并对爆震线路与插头进行检查,如未能发现故障还需布设零时线进行排查;对气缸内气面门以及气门座等位置的积碳情况进行检查,排查气缸内部是否存在泄露情况,先用气缸压表测量,如无异常也可进行拆缸检查。
Install a new sensor to determine whether the original sensor has fault problems, and check the knock circuit and plug. If no fault is found, it is necessary to arrange a zero time line for troubleshooting; Check the carbon deposition at the air valve and valve seat in the cylinder, check whether there is leakage inside the cylinder, measure with the cylinder pressure gauge first, and disassemble the cylinder for inspection if there is no abnormality.
此外在启动过程中,通常会出现启动时电机无转速电池电压恒定不变的情况,有时也会发生盘车有速度但机组难以启动的现象这一现象产生的直接原因通常为电池容量不足接线电缆出现损毁;火花塞等点火系统出现故障;启动电机出现故障问题;启动压力不足等原因。
In addition, in the process of startup, the motor has no speed and the battery voltage is constant. Sometimes, the turning gear has speed but the unit is difficult to start. The direct cause of this phenomenon is usually the insufficient battery capacity and the damage of the wiring cable; Failure of ignition system such as spark plug; Failure of starting motor; Insufficient starting pressure, etc.
燃气发电机组在使用期间可能会出现这样那样的问题,所以为了更顺利的使用起来,建议早些了解相关早些预防,关注我们http://www.huannengpower.com,带你了解更多!
Problems may occur during the use of the gas generator set. Therefore, in order to use it more smoothly, it is recommended to learn about the relevant problems and prevent them earlier and pay attention to us http://www.huannengpower.com Yes, I'll show you more!