你好,欢迎来到济南济柴环能燃气发电设备有限公司官方网站!

沼气天然气瓦斯发电机组点火提前角的检查

来源:http://www.huannengpower.com   发布于:2017-10-30

1、12缸、6缸发动机磁电机点火系统
1, 12 cylinder, 6 cylinder engine magneto ignition system
松开磁电机与齿轮箱连接的两螺栓,顺时针或逆时针旋转磁电机,即可调整点火提前角。面向磁电机正面面板,把磁电机按顺时针方向旋转,可将点火提前角向滞后方向调整(调小)约6.7°曲轴转角;把磁电机按逆时针方向旋转,可将点火提前角向提前方向调整(调大)约6.7°曲轴转角。
Loosen the two bolts connected to the gear box and rotate the motor clockwise or counterclockwise to adjust the ignition advance angle. The magnet motor front panel, the magnet motor rotates clockwise, the ignition advance angle to the direction of adjustment (small) lag about 6.7 degree crank angle; the magnet motor rotates counterclockwise, the ignition advance angle to adjust the direction of advance (turn) of about 6.7 degree crank angle.
每次调节完毕后,再用拖动法检验,直到调整到需要的精确值。
After each adjustment, then drag test, until adjusted to the exact value required.
2、点火盒数字点火系统
2. Ignition box digital ignition system
调节点火控制器侧面的调节旋钮,即可调整点火提前角。向数字增大的方向调节(顺时针调节)旋钮,点火提前角增大;向数字减小的方向调节(逆时针调节)旋钮,点火提前角减小。

QQ截图20171025151917.jpgThe ignition advance angle can be adjusted by adjusting the adjusting knob on the side of the ignition controller. Adjust the direction of the digital increase (clockwise adjustment) knob, ignition advance angle increases; to reduce the number of directions to adjust (counterclockwise adjustment) knob, ignition advance angle decreases.
3、4缸发动机磁电机点火系统
Magneto ignition system for 3 and 4 cylinder engines
当需要调整点火提前角时一,可以通过改变两个线圈的位置,从而实现调整点火提前角的大小。
When the ignition advance angle needs to be adjusted, the ignition advance angle can be adjusted by changing the position of the two coils.
松开感应线圈与导向盘连接的螺栓,顺时针或逆时针移动两个感应线圈,即可调整点火提前角的大小,站在输出端,面向飞轮,顺时针移动感应线圈,可将点火提前角调小,逆时针移动感应线圈,可将点火提前角调大。调整完毕后,使两个感应线圈处在同一条同心直线上并紧固。每次调节完毕后,再用倒拖法检验,直到调整到需要的精确值。
Loosen the induction coil and the guide plate of the bolt connection, clockwise or counterclockwise movement of two induction coils, you can adjust the ignition advance angle size, standing on the output side, facing the flywheel, moving clockwise induction coil, the ignition advance angle is small, moving counterclockwise induction coil, the ignition advance angle adjustment. After adjustment, make the two induction coils in the same concentric line and fasten. After each adjustment, check with the pull back method until the exact value is needed.
更多的关于沼气发电机组的问题或者详细的内容,请进入我们公司的网站:http://www.huannengpower.com 网站中会有很多的内容仅供参考。
More questions about biogas generators or detailed content, please go to our company's website: http://www.huannengpower.com website will have a lot of content for reference only.

上一篇:瓦斯发电机组配气机构介绍
下一篇:沼气发电机组的组成需要哪些部件?