你好,欢迎来到济南济柴环能燃气发电设备有限公司官方网站!

瓦斯发电机组机油冷却器简介

来源:http://www.huannengpower.com   发布于:2017-10-23

瓦斯发电机组工作时,冷却水从机油冷却器前盖进水口进入,经过铜管内部,从后盖出水口流出。机油则从壳体右下侧进油口进入,穿过铝翼管间缝隙,按隔板限制方向迁回流动,从壳体左上侧的出油口流出。机油与冷却水流向相反,通过铜管和铝翼管进行热量交换,从而达到用冷却水降低机油温度的目的。

When the gas generating unit works, the cooling water enters from the water inlet of the front cover of the oil cooler, and passes through the inner copper pipe and flows out from the water outlet of the rear cover. The oil enters the oil inlet from the right lower side of the shell, passes through the gap between the aluminum wing tubes, flows back to the flow in the restricted direction of the clapboard, and flows out from the oil outlet at the left upper side of the shell. The oil is opposite to the cooling water flow, and the heat exchange is carried out by the copper tube and the aluminum fin tube, so as to reduce the oil temperature by cooling water.

瓦斯发电机组余热回收

机油冷却器前、后盖上方各有一个放气阀,在添加瓦斯发电机组低温内循环水时将其旋开,可将冷却水里的空气排出,防止产生气阻影响冷却效果。

There is a vent valve at the top of the oil cooler and the back cover of the oil cooler. When the circulating water is added to the gas generator set, it will be unscrewed. The air in the cooling water can be discharged to prevent the air blocking and affect the cooling effect.

机油冷却器前、后盖下方各有一个放水螺塞,当环境温度低于5℃时,停车将放水螺塞和放气阀同时旋开,可放净机油冷却器内的积水,以免冻坏铜管、铝翼管和前、后盖。有条件的用户可从一侧放水螺塞或放气阀座孔处接上压力588kPa的压缩空气,向内吹4-5分钟,直到另一侧放水孔处看不到往外喷水气为止。

The oil cooler of the front and the back cover below each have a drain screw and when the ambient temperature is lower than 5 DEG C, parking will drain plug and a bleed valve and turn on the net, can put the water in the oil cooler, to avoid freezing the brass, aluminum wing tube and the front and rear cover. Conditional users from one side drain plug or discharge valve seat hole connected with the pressure of the compressed air blowing inward 588kPa, 4-5 minutes, until the other side drain hole can not see the water spray out so far.

机油冷却器外壳上、下方各有一个油塞。在更换机油滤清器滤芯前,将两油塞同时旋开,可放净机油冷却器内的机油,以免将机油滤清器滤芯拉出时流出过多的机油、弄脏瓦斯发电机组。

There is an oil plug on the top and bottom of the oil cooler shell. Before changing the filter element of the oil filter, the two oil plug is unscrewed at the same time, the oil in the oil cooler can be put off, so as to avoid excessive oil from the oil filter element pulling out and fouling the gas generator set.

本文由瓦斯发电机组友情奉献,更多有关的知识请点击:http://www.huannengpower.com我们将用先进的技术,真诚的态度,为您提供为全面的服务。我们将会陆续向大家奉献,敬请期待。

In this paper, the gas generating unit friendship dedication, more relevant knowledge please click: http://www.huannengpower.com, we will use the most advanced technology, the most sincere attitude, to provide you with the most comprehensive service. We will continue to dedicate to you, please look forward to.


上一篇:燃气发电机组的优点
下一篇:内燃式焦炉煤气发电机组的性能介绍