Running in is very important in the use of diesel generator set. Many people do not fully run in the diesel generator set after purchasing the diesel generator set, or the way of running in is incorrect, which is very unfavorable to the performance reliability and service life of the diesel generator set. The following is to explain why the diesel generator set To run in, and the importance of running in.

柴油发电机组在使用过程中磨合的重要性

The importance of running in of diesel generator set in use

不光是柴油发电机组，在日常生活中大家都知道新买回来的汽车或者摩托车一类的机动车都会进行磨合，其实就是对发动机进行磨合，一般情况下，只有全新的发电机组和经过大修后的发电机组才需要进行磨合，柴油发电机组进行磨合主要是为了保证发动机组内部的零件之间充分的接触、摩擦、适应和定型的基本里程。

Not only the diesel generator set, in daily life, we all know that new cars or motorcycles will be run in. In fact, it is running in the engine. Generally, only the new generator set and the overhauled generator set need to be run in. The main purpose of running in the diesel generator set is to ensure the internal stability of the engine set The basic mileage of full contact, friction, adaptation and shaping between parts.

在磨合期可以调整提升柴油发电机组内部各个零件之间适应环境的能力，并磨合掉零件上的不平整的凸起物，从而减小零件之间的摩擦力，为以后柴油发电机组投入工作中使用奠定良好的基础。

During the running in period, the ability to adapt to the environment between the internal parts of the diesel generator set can be adjusted and improved, and the uneven bumps on the parts can be run in, so as to reduce the friction between the parts and lay a good foundation for the use of the diesel generator set in the future.

柴油发电机组磨合的好坏直接会决定到后期柴油发电机组使用中的可靠性、安全性、以及使用寿命、耗油量等产生重要的影响，这是因为新出厂的柴油发电机组虽然在出场前也进行了磨合，但是在组装、装配件等过程中难免会出现小的误差与短时间内检测不出的故障隐患，柴油发电机组内部的各个零部件上面如果有凸起的金属颗粒。

The running in of diesel generator set will directly determine the reliability, safety, service life and fuel consumption of the diesel generator set in the later stage. This is because although the new diesel generator set has been running in before leaving the factory, it is inevitable that there will be small errors and problems that cannot be detected in a short time in the process of assembly Hidden trouble, if there are protruding metal particles on the internal parts of diesel generator set.

在摩擦过程中脱落会使得零件之间的磨损加剧，落入机油中后还会使得机油的质量下降，影响机油对发动机的润滑效果，所以新买的柴油发电机组或者是经过大修过后的柴油发电机组都需要进行磨合才能投入到工作中使用。

In the friction process, falling off will aggravate the wear between the parts, and the quality of the oil will decline after falling into the oil, which will affect the lubricating effect of the oil on the engine. Therefore, the newly purchased diesel generator set or the diesel generator set after overhaul need to be run in before they can be put into use.

如果柴油发电机组没有进行磨合会大大降低其后期的使用性能和可靠性，严重时还会导致柴油发电机组组出现较大的故障而停机，柴油发电机组的耗油量升高等等问题，所以柴油发电机组的磨合非常重要，对柴油发电机组的后期使用会产生很大的影响。

If the diesel generator set does not run in, its later performance and reliability will be greatly reduced. If it is serious, it will cause the diesel generator set to shut down due to large failure, and the fuel consumption of the diesel generator set will increase. Therefore, the running in of the diesel generator set is very important, which will have a great impact on the later use of the diesel generator set.

在此提醒大家，新买的柴油发电机组由于零件之间的摩擦阻力比正常时期要大，所以相对的油耗也会比较高，这是属于正常现象，大家不必担心，将柴油发电机组磨合好可以使得后期的工作中减少很多不必要的麻烦，提升工作效率。

Here, I would like to remind you that the friction resistance between the parts of the newly purchased diesel generator set is greater than that in the normal period, so the relative fuel consumption will be higher. This is a normal phenomenon. You don't have to worry. Running in the diesel generator set well can reduce a lot of unnecessary troubles in the later work and improve the work efficiency.