你好,欢迎来到济南济柴环能燃气发电设备有限公司官方网站!

瓦斯发电机组飞轮齿圈毛病和处理办法是什么?

来源:http://www.huannengpower.com   发布于:2019-10-22

  瓦斯发电机组长时间运用难免会呈现问题,瓦斯发电机组小编向您引见下瓦斯发电机组飞轮齿圈毛病及处理办法一、毛病缘由1、瓦斯发电机组的起动机与飞轮齿圈啮合不良,有时会发作撞击,形成齿轮损坏或单面磨损。若牙齿连续三个以上损坏或磨损严重,起动机齿轮与齿圈牙齿便难以啮合。

  It is inevitable that there will be problems when gas generator is used for a long time. The small group of gas generator sets introduces to you the problems and solutions of flywheel gear ring of gas generator sets. 1. The starter and flywheel gear ring of gas generator set don't mesh well, sometimes they collide, resulting in gear damage or single side wear. If more than three teeth are damaged or severely worn, it is difficult for the starter gear to mesh with the ring gear teeth.

  2、瓦斯发电机组粘缸体。发起机温渡过高时熄火,发起机体内的热量难以分发进来,高温下活塞环和气缸发作粘连,冷却后瓦斯发电机组无法启动。

  2. The gas generator unit is stuck to the cylinder block. When the temperature transition of the engine is too high, the engine will be flamed out, and the heat in the engine body is difficult to be distributed. Under high temperature, the piston ring and the cylinder are stuck, and the gas generator set cannot be started after cooling.

  3、瓦斯发电机组曲轴抱死。由于光滑系统毛病或者机体短少机油形成无法光滑,终招致曲轴抱死发起机无法启动。

  3. The crankshaft of gas generator set is locked. Because of the problem of the smooth system or the lack of engine oil, the engine can not be started.

  4、瓦斯发电机组喷油泵柱塞卡死。

瓦斯发电机组

  4. The plunger of fuel injection pump of gas generator unit is stuck.

  瓦斯发电机组

  Gas generator set

  二、修复办法

  II. Repair methods

  1、若飞轮齿圈有三个以上牙齿损坏,与起动机相对时会招致两者齿轮无法啮合。这种状况,能够用撬棒将飞轮齿圈撬转一个角度,重新启动。损坏的飞轮齿牙可普通能够焊接,严重时需求改换飞轮齿圈及起动机。

  1. If more than three teeth of flywheel ring gear are damaged, the two gears will not mesh when they are opposite to the starter. In this case, the flywheel ring gear can be levered to an angle with a crowbar and restarted. The damaged teeth of flywheel can be welded normally. In serious cases, the flywheel ring gear and starter need to be replaced.

  2、飞轮齿圈牙齿单边磨损严重时,可将齿圈压下,前后端面翻转后,再装在飞轮上运用。

  2. When the single side of the flywheel ring gear teeth is seriously worn, the ring gear can be pressed down, the front and rear end faces can be turned over, and then installed on the flywheel for use.

  3、经检查齿轮啮合正常,起动时飞轮不转动,则应视为发起机内部毛病,如曲轴抱死,活塞粘缸,离合器卡滞等,对此应进一步察看。可先查离合器有无破损卡滞,再检查喷油泵柱塞能否卡滞和发起机内部有无异物等毛病。

  3. After checking that the gear engagement is normal and the flywheel does not rotate when starting, it should be regarded as the internal fault of the starter, such as the crankshaft is locked, the piston is stuck to the cylinder, the clutch is stuck, etc., which should be further observed. First check whether the clutch is damaged and stuck, then check whether the plunger of the fuel injection pump is stuck and whether there is any foreign matter in the initiator.

  以上是瓦斯发电机组厂家为大家介绍的相关内容,想要了解更多内容,欢迎访问网站:http://www.huannengpower.comThe above is the related content introduced by the manufacturer of gas generator set. For more information, please visit the website: http://www.huannengpower.com


上一篇:沼气发电机组对沼气有什么要求呢?工作原理是什么?
下一篇:燃气发电机组:发电机失磁缘由及处理方法!