欢迎进入济南济柴环能燃气发电设备有限公司官网!
当前位置:首页 - 新闻中心 - 发电机知识

发电机知识

发电机组进行充电时充不进电怎么办?

返回 2022.03.18 来源:http://www.huannengpower.com 0
燃气发电机组厂家认为出现这种问题有可能是保险丝或整流二极管损坏所造成的。当保险丝烧断后,充电机电源指示灯不亮;整流二极管损坏后,充电机的电源指示灯亮,但无直流电输出。
The manufacturer of gas generator set believes that this problem may be caused by the damage of fuse or rectifier diode. When the fuse is blown out, the charger power indicator does not light up; After the rectifier diode is damaged, the power indicator of the charger is on, but there is no DC output.
1、充电机变压器被烧坏。
1. The charger transformer is burnt out.
2、充电机上的二极管被烧坏。
2. The diode on the charger is burnt out.
3、充电机的充电电流表损坏。
3. The charging ammeter of the charger is damaged.
4、充电机的保险丝被烧坏。
4. The fuse of the charger is burnt out.
排除故障的方法就是:断开充电机与蓄电池的连接线,用万用表直流电压挡(50V)测试充电机两个输出接线柱间的电压,注意红表笔接充电机的正极,黑表笔接负极,发现无电压输出。
The troubleshooting method is: disconnect the connecting wire between the charger and the battery, test the voltage between the two output terminals of the charger with the DC voltage gear (50V) of the multimeter, and pay attention to the red probe connected to the positive pole of the charger and the black probe connected to the negative pole. It is found that there is no voltage output.
拆下充电机外壳,对充电保险芯子进行检查,发现60A的保险芯子烧坏。更换后,充电机恢复正常充电,故障即被排除。
Remove the charger shell and check the charging fuse core. It is found that the fuse core of 60A is burnt out. After replacement, the charger will resume normal charging and the fault will be eliminated.
想要了解更多关于发电机知识,关注我们网站http://www.huannengpower.com可以查看更多内容。
To learn more about generators, follow our website http://www.huannengpower.com You can see more.
新闻搜索
济南济柴环能燃气发电设备有限公司
  • 服务热线

    0531-62325028
    0531-69951266

发电机组进行充电时充不进电怎么办?

燃气发电机组厂家认为出现这种问题有可能是保险丝或整流二极管损坏所造成的。当保险丝烧断后,充电机电源指示灯不亮;整流二极管损坏后,充电机的电源指示灯亮,但无直流电输出。
The manufacturer of gas generator set believes that this problem may be caused by the damage of fuse or rectifier diode. When the fuse is blown out, the charger power indicator does not light up; After the rectifier diode is damaged, the power indicator of the charger is on, but there is no DC output.
1、充电机变压器被烧坏。
1. The charger transformer is burnt out.
2、充电机上的二极管被烧坏。
2. The diode on the charger is burnt out.
3、充电机的充电电流表损坏。
3. The charging ammeter of the charger is damaged.
4、充电机的保险丝被烧坏。
4. The fuse of the charger is burnt out.
排除故障的方法就是:断开充电机与蓄电池的连接线,用万用表直流电压挡(50V)测试充电机两个输出接线柱间的电压,注意红表笔接充电机的正极,黑表笔接负极,发现无电压输出。
The troubleshooting method is: disconnect the connecting wire between the charger and the battery, test the voltage between the two output terminals of the charger with the DC voltage gear (50V) of the multimeter, and pay attention to the red probe connected to the positive pole of the charger and the black probe connected to the negative pole. It is found that there is no voltage output.
拆下充电机外壳,对充电保险芯子进行检查,发现60A的保险芯子烧坏。更换后,充电机恢复正常充电,故障即被排除。
Remove the charger shell and check the charging fuse core. It is found that the fuse core of 60A is burnt out. After replacement, the charger will resume normal charging and the fault will be eliminated.
想要了解更多关于发电机知识,关注我们网站http://www.huannengpower.com可以查看更多内容。
To learn more about generators, follow our website http://www.huannengpower.com You can see more.