Trouble shooting of flywheel ring gear of gas generator set

　　瓦斯发电机组长时间运行难免会出现问题，今天小编为您介绍一下瓦斯发电机组飞轮齿圈故障及解决方案

　　There will inevitably be problems when gas generator runs for a long time. Today, I will introduce the flywheel gear ring fault of gas generator and Its Solutions

　　一、失败原因

　　1、 Reason for failure

　　1. 瓦斯发电机组起动器与飞轮齿圈啮合不良，有时会发生碰撞，造成齿轮损坏或单面磨损。如果齿面连续损坏或严重磨损超过三次，则启动齿轮和齿圈很难啮合。

　　1. The starter of gas generator set and flywheel ring gear are not meshed well, sometimes there will be collision, resulting in gear damage or single side wear. If the tooth surface is damaged continuously or severely worn more than three times, it is difficult for the starting gear and ring gear to mesh.

　　2、带气缸体的瓦斯发电机组。当发动机温度过高时，发动机会熄火，发动机内部的热量难以散发，活塞环与气缸在高温下粘连，气体发生器冷却后无法启动。

　　2. Gas generator set with cylinder block. When the engine temperature is too high, the engine will shut down, the heat inside the engine is difficult to be dissipated, the piston ring and the cylinder are adhered under high temperature, and the gas generator cannot be started after cooling.

　　3、瓦斯发电机组曲轴抱枕。由于润滑系统故障或机油不足而导致润滑失败，更终导致曲轴锁定发动机而无法启动。

　　3. Gas generator set crankshaft bolster. The failure of lubrication due to the failure of the lubrication system or the lack of oil eventually results in the engine being locked by the crankshaft and unable to start.

　　4、燃气发生器喷射泵柱塞堵塞。

　　4. The plunger of injection pump of gas generator is blocked.

　　二、修复方法

　　2、 Repair method

　　1. 如果飞轮的齿轮环上有三颗以上的齿被损坏，如果这两颗齿对着起动机，就不能啮合。在这种情况下，您可以使用撬棒撬车轮环周围的角度和重新启动。损坏的飞轮齿一般可以焊接，严重的需要更换飞轮齿圈和起动机。

　　1. If more than three teeth on the flywheel gear ring are damaged, if the two teeth are facing the starter, they cannot be engaged. In this case, you can use a crowbar to pry the angle around the wheel rings and restart. The damaged flywheel gear can be welded generally, and the flywheel gear ring and starter need to be replaced seriously.

　　2. 若飞轮齿圈一侧齿面磨损严重，可将齿圈压下，前后端面翻转后再装上飞轮使用。

　　2. If the tooth surface of one side of the flywheel ring gear is seriously worn, the ring gear can be pressed down, the front and rear end faces can be turned over, and then the flywheel can be installed for use.

　　3、检查齿轮啮合是否正常后，启动时飞轮不转，应视为发动机内部故障，如曲轴抱死、活塞卡死气缸、离合器卡死等，应进一步观察。检查离合器是否损坏，然后检查注射泵柱塞是否卡住，发动机是否有异物等故障。

　　3. After checking whether the gear meshing is normal, if the flywheel does not rotate when starting, it shall be regarded as the internal fault of the engine, such as the crankshaft locking, the piston jamming the cylinder, the clutch jamming, etc., which shall be further observed. Check whether the clutch is damaged, then check whether the plunger of the injection pump is stuck, and whether the engine has foreign matters and other faults.

　　以上是瓦斯发电机组厂家为大家介绍的相关内容，想要了解更多内容，欢迎访问网站：http://www.huannengpower.com

　　The above is the related content introduced by the manufacturer of gas generator set. For more information, please visit the website: http://www.huannengpower.com